Ecler MIMO1212SG

verkaufe neue Audio Matrix, wäre für eine installation gedacht gewesen die dann nichts wurde , geräte wurde nur konfiguriert nicht verbaut

hier ein paar Daten vom Hersteller:

Miscellaneous

Management Connectivity Ethernet Base-Tx 10/100Mb Auto X-Over CAT5 up to 100m

Remote Bus Over twisted pairs; up to 1km (see specific specs.)

GPI 8, from 0 to 10VDC or TTL level

Aux. Power Supply for Remotes & GPI +12VDC, 1.2A. max. (short circuit protected)

Time and date retention (battery) 100 hours approx. (ambient temperature dependant)

RTC accuracy ±1 minute / month


DSP 2x 32/64bit Sampling Rate 48kHz

Latency IN to OUT <3.2ms

Converters Resolution 24bit AKM

Dynamic Range AD:110dB, DA: 115dB

Analogue 12 Input/Output Terminal block (Symmetrical)

Analogue Input headroom +27dBV = +30dBu

Max. output level +18dBV = +21dBu

Input sensitivity @ 0dBV out From -50dBV to +10dBV in 0.5dB step

Input Impedance Balanced, >4kΩ

Phantom power +42VDC, 5mA max. software switched

Frequency response (-3dB) 5Hz to 24kHz

Flatness better than ±0.1dB

THD+Noise @ 1kHz, 0dBV input (line) <0.004%

THD+Noise @ 1kHz, -40dBV input

(mic.)

<0.008%

Output Noise floor FFT (20Hz - 20kHz) better than 115dB

Interchannel crosstalk (20Hz - 20kHz) better than 90dB (100dB typ.)

Channel Leakage (20Hz - 20kHz) better than 100dB (115dB typ.)

CMRR 20Hz- 20kHz 65dB typ.

Processing

Input Level (x12) Range: from Off to 0 dB

Mute: Yes

Signal Polarity reverse: Yes

Metering: VU + clip pre & post fader

19

Output Level (x12)

Range: from Off to 0 dB

Mute: Yes

Solo: Yes

Signal Polarity reverse: Yes

Metering: VU + clip pre & post fader

Output Gain (x12)

Range: from 0 to +6 dB

Input Delay (x12)

from 0 to 1000 ms.

Units: sec/ms/m/cm.

Output Delay (x12)

from 0 to 1000 ms.

Units: sec/ms/m/cm.

Parametric Eq. Types (4 max per input) (6 max per input)

Bypass / On-Off all channels

Param Eq. Freq: 20Hz-20kHz; Gain: -60/+12 dB; Q: 0.3 to 200

Low & High Shelf 6/12 dB/oct

Low & High Pass 6/12 dB/oct

All Pass 1/2 order

High & Low pass output Crossover filters (x12)

Bypass On-Off

Butterworth in 6/12/18/24 dB/oct

Bessel in 12/18/24 dB/oct

Linkwitz-Riley in 12/24 dB/oct

Input Noise Gate (x12)

Bypass On-Off

Threshold: from –80 dBV to +18 dBV

Depth: 0 dB to 80 dB

Attack time: from 0,1 ms. to 500 ms.

Hold time: from 10 ms. to 3000 ms.

Release time: from 10 ms. to 1000 ms.

Input Compressor / Limiter (x12)

Bypass On-Off

Threshold: from –36 dBV to +18 dBV

Ratio: 1:1 to inf:1 (limiter)

Knee: hard / soft

Attack time: from 0,1 ms. to 500 ms.

Release time: from 10 ms. to 1000 ms.

Make up gain: from 0 to +10 dB

Input Frequency Shifter (x4)

(Feedback Loop Reducer)

Available on IN1 to IN4. ON / OFF function

Output Limiter (x12)

Bypass On-Off

Threshold: from –36 dBV to +18 dBV

Attack time: from 0,1 ms. to 500 ms.

Release time: from 10 ms. to 1000 ms.

Built in Signal Generator

Sine: from 20 Hz to 20 kHz

Polarity: from 20 Hz to 20 kHz

White noise

Pink noise

Stereo Linking

Adjacent input / output channels

Linked processing

Matrix routing linked

Mix Matrix

Size: 12x12

Vol: Input, Output, Crosspoint

Mute: Set/Clear individual, row, column, all

Input /output Mono/stereo selector

Meter: Input /output VU and clip

20

Pager (x3)

Input: IN1 to IN12

Priorities: 3 (1 max, 3 min)

Depth: 0 dB to 80 dB

Attack time: from 5 ms. to 2000 ms.

Release time: from 50 ms. to 3000 ms.

Chime Source: None, Melody 1, Melody 2

Chime Volume: from –12 dB to 0 dB

Mechanical

Dimensions (WxHxD)

482.6 x 44 x 253 mm / 19 x 1.73 x 9.96 in.

Weight

3.2kg

Supply

Mains

90-264VCA 47-63Hz

Power consumption

75VA

Miscellaneous

Management Connectivity

Ethernet Base-Tx 10/100Mb Auto X-Over CAT5 up to 100m.

Remote Bus