Meyer Sound UM-1P Stage Monitor

Meyer Sound UM-1P Stage Monitor, 12 inch floor monitor
Order now: https://cuesale.com/product/meyer-sound-um-1p-stage-monitor/


Including flightcase when buying 2 pieces

The UM-1P self-powered stage monitors are designed for high-level, full-bandwidth monitoring, cleanly reproducing stage mixes that include vocals and musical instruments. These units provide efficient response down to 60 Hz. The compact enclosure houses a 12-inch cone driver and a 3-inch-diaphragm compression driver. The combination of high-performance drivers and perfectly matched drive electronics yields flat amplitude and phase response plus near-perfect impulse response over the full audio bandwidth with benefits including lower susceptibility to feedback. Maximum SPL is 133 dB at one meter, with exceptionally low distortion.
The UM-1P provides a narrow, symmetrical beamwidth of 45 degrees horizontal and vertical, allowing close placement of monitors with minimal interaction between them.

The constant-Q design of the high-frequency horns provides uniform beamwidth across the entire operating range in both the horizontal and vertical planes. Attenuation outside the beamwidth is rapid and uniform at all frequencies, with minimal side lobing.
Each driver is individually powered by a dedicated channel of the proprietary class AB/bridged amplifier with complementary MOSFET output stages. Total power is 550 watts. The incoming audio signal is processed through an electronic crossover and correction filters for flat phase and frequency response as well as for driver protection. Phase-corrected electronics ensure flat acoustical amplitude and phase response, resulting in exceptional impulse response and precise imaging.

Acoustical :

Operating Frequency Range : 60 Hz – 18 kHz
Frequency Response : 65 Hz – 17 kHz ±4 dB
Phase Response : 500 Hz – 16 kHz ±35°
Maximum Peak SPL : 133 dB
Dynamic Range : >110 dB
Crossover : 1000Hz
Transducers :

Low frequency :
One 12″ cone driver
Nominal impedance: 2 Ω Voice coil size: 3″
Power-handling capability: 400 W (AES)
High frequency :
One 3″ compression driver
Nominal impedance: 16 Ω Voice coil size: 3″
Diaphragm size: 3″
Exit size: 1.4″ throat
Power-handling capability: 100 W (AES)
Audio Input :

Type : Differential, electronically balanced
Maximum Common Mode Range : ±15 V DC, clamped to earth for voltage transient protection
Connectors : Female XLR input with male XLR loop output or VEAM all-in-one (integrates AC, audio and network)
Input Impedance : 10 kΩ differential between pins 2 and 3
Wiring :
Pin 1: Chassis/earth through 220 kΩ, 1000 pF, 15 V clamp network to provide virtual ground lift at audio frequencies
Pin 2: Signal +
Pin 3: Signal – (optional polarity reversal switch)6
Case: Earth ground and chassis
DC Blocking : Differential DC blocking up to maximum common mode voltage
CMRR : >50 dB, typically 80 dB (50 Hz – 500 Hz)
RF Filter : Common mode: 425 kHz; Differential mode: 142 kHz
TIM Filter : <80 kHz, integral to signal processing
Nominal Input Sensitivity : 0 dBV (1 V rms, 1.4 V pk) continuous average is typically the onset of limiting for pink noise and music
Input Level : Audio source must be capable of producing a minimum of +20 dBV (10 V rms, 14 V pk) into 600 Ω to produce maximum peak SPL over the operating bandwidth of the loudspeaker
Amplifier :

Type : Two-channel complementary MOSFET output stages (class AB/bridged)
Output Power : 550 W total
THD, IM, TIM : <.02 %
Load Capacity : 2 Ω low channel, 16 Ω high channel
Cooling : Convection; 24 V DC output for optional external fan


€1125,00 Ex V.A.T. (MwST) per piece.

Prices are Excluding 21% VAT / MwSt.

Products are located in The Netherlands, customers with a V.A.T. ID number pay 0% V.A.T. / MwSt
Please send us your full address for a shipment quote / price.

For more used equipment check our other advertisements on this site or have a look at our website www.cuesale.com